E30 Zone

Hi everyone,

Just wondering if anyone has the pin out for this connector under the dash. I only have six wires used in mine.

Thanks,

Martin.

Hi everyone,

Just wondering if anyone has the pin out for the wires in this connector going into the dash? I’ve only got 6 wires used on mine.

Thanks,

Martin.

Hi,

Could I please have a price for a head gasket. BMW part number 1722524.

Thanks,

Martin.

Thanks Jon. Payment sent via PayPal.

Hi,

Would it be possible to get a price and availability on a throttle clip for an M42 engine? Part number is 13541288013.

Thanks,

Martin.

Hi,

Could I please have a price for a three crush spacers for a 188mm diff. BMW part number- 33121744368”a.

I will need them posting so please let me know how much this would be too.

Thanks,

Martin.

Nice job there, fair do's. So would the e36 6 speed be a bolt in swap? I presume it would as I currently run an e36 5 speed.

Can anyone tell me if the e46 320d has the same bolt pattern bell housing as an m42 engine? I'm pretty sure it does, but want to che check before I buy one.

Thanks, Martin.

rix313 wrote:I'm keen to get mine on some scales and see what it weighs when its back together. Not sure what to expect.

Snap! I'm hoping to get mine on the road for the end of the year and will get it on the scales then, with alot less weight than it had last time it was on the road.

In short, it's near impossible to measure it without a dedicated test rig. The spool would need to be loaded up to various torques, held against the output shafts, then the torque resistance between both shafts measured by independently rotating them... Not an easy task! :D This is why the lock is ...

Just wondering how light anyone has managed to get there e30?

Thanks for the reply Andrew. That makes alot of sense.

So if we did want to measure the minimum torque value to reach maximum lock, how would you go about that?

Cheers, Martin.

Have you sorted this yet? I can scan the pages for you tomorrow if you want. Let me know.

Cheers, Martin.

Would it be possible to get a price on just the internals for the bonnet and boot? I bought a bonnet and boot on a group buy a while ago and have never fitted them because I didn't really want them just on pins. If I could get the internals, I could bond them on myself and job done!

Thanks, Martin.

Thanks for the reply Gareth. So millrats post is right then? Is there a way of actually measuring it? I would presume you would have to put a given amount of torque into the diff and somehow rig a torque meter up to the output shafts.

A question; the "percentage lock" is not an accurate method to describe the amount of resistance as "percentage lock" relates to the engine power/torque. Therefore, isn't stating the breakaway torque a better measurement? I ask this because as I understand it, 70% lock equals a breakaway torque of ...

Hi, could you give me a price please for-

11141734422
11141247849
11141247837
11141721802
11141721919
One of each.

Thanks, Martin.

Could I have a price for the following please-

1no- 64118391141- Bulk head connector,
2no- 64118379131- Seals,
1no- 11531721172- Gasket,
1no- 11531714738- Engine connector,
1no- 11531709157- O ring.

Thanks, Martin.

Hi,

I am looking for some shims for a BMW E30 medium case diff. Are they available for the pinion? And are they also available for the crown wheel (they sit between the main casing and the caps either side).

Many thanks, Martin.

Can't seem to find any Torque settings for inside the diff (ie crown wheel bolts, LSD end plate bolts, etc). They're not listed in the sticky at the top of the page and I can't seem to find them anywhere else. Can anyone help?

Cheers,

Martin.

Could you please give me prices for the seals in an E30 medium case diff. Part numbers- 2no 33107505602 (44x67x10mm seal) 1no 33101214099 (45x75x10mm seal) 1no 33111210405 (casing gasket) Also, if possible the two O rings that seal the output flanges and the crush spacer that sits between the two be...

Yep, count me in! I did try to call today but no answer, so will try again tomorrow and leave a message if your all busy.

Thanks, Martin.

Am I too late to add to this? I could do with a boot and bonnet.

I need to machine the ramp angles on my LSD from 45degrees to 30degrees but everyone I ask can't do it. Does anyone know a machinist that can?

Thanks in advance, Martin.

I seem to remember A good while ago there was a moderator on here (Ant?) selling chips but can't remember if it was just for the m42? Are they still available? Any other alternatives?
Sorry, Ive not been on here for a while.
Thanks, Martin.

Brett, just had a look on that site and the nearest part to what I need is a complete LSD. I just need the friction plates from inside the LSD. I would of thought they would be available, as they are a wearing part.
Thanks, Martin.

Hi brett. Yes, reg e357 cvm chasis no wbaab320802860517 thanks, martin.

Could do with a price for 8 new friction plates for a medium case diff.
I will probably need some other bits for it aswell, I someone has a parts diagram?
Thanks, Martin.

martinallwood@hotmail.com

I'd be interested in a new z3 rack for £130 too!!!

Can anyone recomend any? And where to get them? For a 318is.
Cheers, Martin.

Did the 318is come with sport suspension (like on the 325i sport) or just standard suspension, from the factory?
Cheers, Martin.

Ok, it should be coming today so i'll try it.
Its only the EDIS coil pack i'm using. Pretty much everything else is BMW with my own loom.
I'll let you know how I get on.
Thanks, Martin.

Ok, I'm having a major change of direction on this. Ive finally got some time to sort it out and am going to bin off the original dash and just have a simple universal tacho with afew other guages and warning lights as well. Ive found out that the DTA ecu sends out a 12v square wave signal. But the ...

Ok, maybe I should check the si batteries then. Where are they.

OK, thanks for the resistors etc FlappySocks, I recieved them last week. I finally had chance to fit them, as your instructions explained. Unfortunatly, after trying both swapping the wires round and twiddling with the potentiometer. I had no movment on the tacho.
Any ideas?
Cheers, Martin.

Search found 88 matches

Under dash connector pin out

Dash plug pin out

Price please- Head gasket

Re: M42 throttle clip

M42 throttle clip

Crush spacer for 188mm diff

Re: e46 gearbox bolt pattern

e46 gearbox bolt pattern

Re: How heavy is yours?

Re:

How heavy is yours?

Re:

Re: M42 ENGINE BUILDING INFO.

Re:

Re:

Re:

M42 Gaskets (price please)

Price please- Heater parts.

Diff shims

Diff Tightening Torques

quote please (Seals etc)

Re:

Re:

Machining LSD Ramp angles

Whats the best Chip for a 318IS with M44 power?

Re: Diff friction plates

Re: Diff friction plates

Diff friction plates

Re: What alternatives to the Z3 rack

Non lowering, uprated dampers?

318is suspension?

Re: How many pulses does the rev counter need?

Re: How many pulses does the rev counter need?

Re: How many pulses does the rev counter need?

Re: How many pulses does the rev counter need?