E30 Zone

Thank you!

Which bellhousing is it that allows the M3 dogleg to be fitted to the M20 engine?

It is just the exhaust guides as they are very poor. I have had some made now as everyone that listed them off the shelf had none in stock with no delivery date.

Bloody expensive to change the valves just because the guides are oversize!

Is there anyone in the UK that keeps valve guides in stock for the M20?

engine is back, just a little bit of fettling to do with the second injector rail before it goes in.

Thanks for that, I`ll check it out tomorrow!

... and a few engine bits, should have it in the car in the next week or so.

There`s very little of the car that follows the same lines if you look closer! We mocked it up before it was fitted and it dosn`t look very nice if you keep the lines constant. You have to remember there is door numbers and sponsors decals etc that need to go on yet. Anyway... a bit more of the buil...

We all like different things

, Yes it`s Jasons old car, hope to have the engine back this week, I`m sure most will like that

Back from the graphics company now.. starting to go back together. http://i87.photobucket.com/albums/k147/spewy555/2011-12-22174120.jpg http://i87.photobucket.com/albums/k147/spewy555/2011-12-22174138.jpg http://i87.photobucket.com/albums/k147/spewy555/2011-12-22174203.jpg http://i87.photobucket.com...

This car is for the Mrs, she insisted leaving it RHD until after I`d done all the work! However I have all the LHD parts so can convert it back later. I use the knotted wire wheels on a grinder and used a gas torch on the bits you can`t get to afterwards. Best way to be honest is an acid dip or oven...

The spit is one we use a lot I just make up the brackets depending on the car.

..and now on the way to the graphics company for a full wrap.

New FIA cage tig welded in. http://i87.photobucket.com/albums/k147/spewy555/2011-09-14091401.jpg Painted inside and underneath. http://i87.photobucket.com/albums/k147/spewy555/2011-10-24075033.jpg http://i87.photobucket.com/albums/k147/spewy555/2011-10-24075108.jpg http://i87.photobucket.com/albums/...

All underseal removed and then seam welded.

Thought you might like to have a look at whats happened to Jasons old M3! http://i87.photobucket.com/albums/k147/spewy555/2011-09-03181015.jpg http://i87.photobucket.com/albums/k147/spewy555/2011-09-03180923.jpg http://i87.photobucket.com/albums/k147/spewy555/2011-09-03180905.jpg http://i87.photobuc...

Need the following:

1 x water pump
1 x oil pump chain
1 x timing chain
1 x small water pump hose

Cheers Andy

Just need 8 valve guides for the exhaust on a 1988 2.3 head. Cheers!

Perfect, I`ve got the right ones then, cheers!

How can I tell if I have a set, is there a number on the piston or could someone put a picture up of one?

Cheers!

Great thanks!

Strange question but does anyone know what the thread pitch and size is?

Cheers guys, there are two braces that run along the top of the arms on some of the cars which also pick up on the spring mount, has anyone got pics of those?

Has anyone got any pictures of the reinforcement on the early grp A arms to hand?

That`s it , thanks! I spend ages trying to find it with the search thingy

Changed to loom to an M20 one but I know one of the wires needs cuttin when plugging into a 1.8 loom, does anyone know which one?

It`s a medium case 4.4 but not sure which 5 series E28 it`s from.

Will it fit in an E30 with just a back cover change or will it require more work?

That`s how mine are finished

Guys , I can do them for you for £25 if it helps, I do a lot for the race boys and if it`s over the weekend I can do them while you wait!

Essex / Suffolk border

Cheers!

Does anyone know how much a complete M20B20 engine weighs? Got to sort a pallet out for someone.

Cheers.

As above really, these are for a race car and was wondering if the 173 ecu is in effect the same as the 320i 172, i.e will a chip for a 173 work in a 172 or are ther other issues. Idle and cold start etc I`m not bothered about.

Probably a bit far for you but I can do them for £25

Am I right in thinking the valves are the same on the standard 2.0 and 2.5 heads, i.e I can fit an inlet from a 2.0 head into a 2.5 head etc? Cheers.

Search found 60 matches

Re: M20 bellhousing question

M20 bellhousing question

Re: M20B25 valve guides

M20B25 valve guides

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

Re: M3 race car build

M3 race car build

M3 S14 parts

M3 S14 valve guides

Re: Pre facelift highe compression pistons for a 325i

Pre facelift high compression pistons for a 325i

Re: Thread size & pitch on diff filler plug?

Thread size & pitch on diff filler plug?

Re: Early Grp A trailing arms

Early Grp A trailing arms

Re: Which wire to cut fitting a 325 into 1.8 shell

Which wire to cut fitting a 325 into 1.8 shell

Re: e28 diff case

e28 diff case

Re: Lightned flywheel on a stock 325i?

Re: Lightned flywheel on a stock 325i?

Re: M20B20 weight

M20B20 weight

325i ECU code 0 261 200 173 can chipped 172 be used instead?

Re: Lightened flywheel

Valve sizes on 2.o and 2.5 M20