E30 Zone

Found one on eBay , problem solved

How’s things ,
The sport has started handling very bad , the bushing in the steering knuckle is on its way out .

Does anyone know where I can buy a solid bush or know if I can just make some thick spacers ?

Thanks in advance

maggspower wrote:Check the other thread you started!!

Sorted that problem. This is a new one.

Will check heater hoses

When revved to 2000 revs it starts tapping. Can feel it tapping inside heater matrix box area

Sounds like a plastic noise right under glovebox. Reved engine whilst feeling gearbox and engine and can't feel a noise . pretty sure its not either. Could it hardly be a short shifter I fitted?

Fully rebuilt my m20b25. When car is revved there's a knocking/tapping sound coming from below glovebox to middle of dash. Gets louder and quicker when going up revs.

No noise on idle, what could this be

Fully rebuilt my m20b25. When car is revved there's a knocking/tapping sound coming from below glovebox to middle of dash. Gets louder and quicker when going up revs.

No noise on idle, what could this be

Brianmoooore wrote:If you want the wires positively identified, I need colours.

. Any ideas Brian?

Got sorted Brian. The little triangle piece on inlet manifold was loose and sucking more air in.

Changed crank position sensor ( from working engine to make sure) -made no difference.
Checked ht leads for any cracks or wear , seam ok no wear.

Any suggestions?

Hi, Just fully rebuilt my 1989 m20b25 with all new everything. Started her up and noticed a very light heek up on idle , more noticeable when you hold car with your hand. The engine revs fine and no splutters. Exhaust is clean with no smoke or steam. The engine sounds perfect but just slightly has t...

Brian. The wires are wrapped in black factory core. In one of wires there are brown and orange and brown and yellow. In the other wire is just all brown and about 4 or 5 wires.

Small one ran to top of starter. But the two together are an earth but I don't know where abouts it earths to. Car runs with it earthed. Didn't check colour but the two wires are shaped to earth at same point.

Won't let me upload photos!!

Doing engine conversion from 320i to 325i. I've put battery in boot with genuine kit. But I can't seem to figure out where these two wires go . one is on starter loom, not sire if its for starter as there's already two wires on starter. Other wire comes out of bulkhead.theres two wires together with...

There seems to be snap rings everywhere. Have the rear casing about 20mm apart from bell housing casing and it still won't come off. There seems to be another inner snap ring inside the rear output shaft bearing but its a squeeze out when it should a sqhueze in grrr...

Got the circlip out, but I still cant remove rear cap off gearbox. I taught front output shaft circlip was holding it. Is there a circlip on rear output shaft?

Got a lend of straight circlip pliers, going to give them a go and see how I get on.

Hi, Currently rebuilding a 240 getrag gearbox from a 320i 1989. I've removed all bolts from rear casing and front output shaft seal holder. But there seams to be a circlip on the bearing on the output shaft. The circlip has no holes to grab with pliers and doesnt move outwards. Any one any suggestio...

bump this up anyone?

anyone?

last place taxed swansea i was told by dvla, reg from london yes.

Date of Liability 01 10 2004
Date of First Registration 20 04 1988
Year of Manufacture 1988
Cylinder Capacity (cc) 2494cc
CO2 Emissions Not Available
Fuel Type PETROL
Export Marker Y
Vehicle Status Unlicensed
Vehicle Colour BLACK
Vehicle Type Approval Not Available

got this from the dvla

Hi,
anybody have any information on this reg, dvla told me it was registered in swansea, but its here now in ireland, just want to know if anyone has a any history or pictures of it , thanks very much

braided lines on and steering pipes on, just have to make up pipes for underneath car and the rear suspension can go up:D whilst putting on of my new caliper nipples in it sheared off:mad: have to use some easy outs to get it out now and put an old one back in :( http://i978.photobucket.com/albums/a...

yous have it really cheap, lowest qoute you can get in ireland is 250 euro. First time drivers in own name your looking at 3000+ , in fathers name 2000+

hi , i sanded down a wing which has been filled and resprayed before, because the red oxide was thick stuff it filles most of the imperfections , 3 small dents to fill, but ill post pics tommorow! Also its a good rust preventative! i think im going with waterbased as cellulose gives off poisonous ga...

Hi,
i am going to be attempting a home respray and underseal in the coming weeks, i shall be making a diy spray booth outside with heavy duty plastic and a wooden frame. As it is outside im just wondering can you prime a car in red oxide to protect it before body prep?

thanks

the price puts me off haha

cant really rememeber, around 65 euro i think ? heres a photo of it fitted, slightly wonky but after its first drive it should settle into right position

i bought a bmw group n m3 diff bush (z3m)

Its reinforced and its a bmw part, dont know the part no. but shouldnet be hard to get

Danthe pipes

holy crap! just goes to show how easy cars can crumple! hope he gets better dude!

Nothing compared to the work gone into yours ! Hopefully we`ll get it there someday. Leaving the underbody and outerbody respray to the profesionals as i think it was you that suggested doing it myself was it?

Alls thats left is to order braided goodridge lines, and caliper nipples and all the suspension is....... DONE!! http://i978.photobucket.com/albums/ae268/finto_316/null_zps82c7fd33.jpg Danthe e36/m20 steering pipes should arrive this week, nice piece of kit the bling up the front haha.... getting th...

Search found 305 matches

Re: Solid steering knuckle bushing

Solid steering knuckle bushing

Re: Knocking noise - engine rebuilt

Re: Knocking noise - engine rebuilt

Re: Knocking noise - engine rebuilt

Knocking noise - engine rebuilt

Knocking noise - engine rebuilt

Re: where do these wires go?

Re: Engine rebuild.. shaky idle

Re: Engine rebuild.. shaky idle

Engine rebuild.. shaky idle

Re: where do these wires go?

Re: where do these wires go?

Re: where do these wires go?

where do these wires go?

Re: gearbox dissassembly problem

Re: gearbox dissassembly problem

Re: gearbox dissassembly problem

gearbox dissassembly problem

Re: E495 MYE 325i se

Re: E495 MYE 325i se

Re: E495 MYE 325i se

Re: E495 MYE 325i se

E495 MYE 325i se

Re: Insurance. What a rip off/joke!

Re: Red oxide primer

Red oxide primer

Re: Diff Bush

Re: Diff Bush

Re: Diff Bush

Re:

Re: Demise of e30 327i

Re:

Re: