E30 Zone

many thanks

I have a question about clutch.

What's the correct combination of clutch control?

A - M3 e30 input cylinder and output cylinder

B - M3 e30 input cylinder and M3 e36 output cylinder

C - M3 e36 input and output cylinder

more troubles with my swap

this is that I found in the intake

and this in the cylinder head

take a look the colour of the oil

fuc*ing battery

[youtube][/youtube]

[youtube][/youtube]

Many thanks Jhonno

Today I buy one bew battery to try to start the engine

Timing is ok, the problem is the battery, I think.

When I change the bearing rods I can spin the engine by hand.

Today I try to spin it another time

Today I try to start the engine, 3 years since I make the swap, and this is the result

[youtube][/youtube]

Maybe the starter motor?

New wheels for my M3

Front 8" rear 9"

The wires from S50 engine that I not use in this swap:

2, 4, 5, 6 7, 9, 16, 17, 22

UweM3 wrote:MODIFY swybar/mounting points.

This modify causes suspensions works bad or not?

Many thanks again

What exhaust is plug and play?

Jhonno wrote:
taper wrote:
Jhonno wrote:Is that the e36 engine plug?

Yes
You need an e30 one... And the correct wiring diagrams to make it plug and play..

Now I still done the connections from the e36 plugs to the e30 plugs, but the rest of pins, appears in the pic, of the e36 they not used

Jhonno wrote:You can cut that positive out yes

From the green arrow, I'm right?

Jhonno wrote:Is that the e36 engine plug?

Yes

Anybody can help me?

I have a trouble with the swaybar.

When the car is unload the swaybar hits the exhaust.

Exists any solutions for this incovenient?

I used the e28 M5 plug, I think it was about £23 from the dealer s, Your suggestion sounds like an ingenious and cheap way around it Geoff, but for me it works out more cost efficient to go into work for an hour's overtime and spend half an hour fitting the M5 chip than spending 2 hours doing mods ...

I use this:

Installed

All of this conections are Ok? http://img197.imageshack.us/img197/7278/img0664k.jpg http://img526.imageshack.us/img526/1669/img0667mt.jpg Can I cut this positive wire from the insulated? http://img44.imageshack.us/img44/8194/img0665i.jpg http://img197.imageshack.us/img197/2036/img0668n.jpg I retired...

This is the conector of the car, with all the original pins become with the car http://img34.imageshack.us/img34/1460/img0652d.jpg and this is the engine conector with teorically all the pins necessary to start the engine http://img34.imageshack.us/img34/3342/img0653kj.jpg What I do with the rest of...

You can use the trottle cable of e36

I install the original cable of my car

E30 M3 with s50b30 engine

One is of a friend and the other is from a workshop

My method

Many thanks!

And where is the correct location to connect the plugs 1 and 2?

what do you think if I bolt the wire number 4 to the green circle nut?

I added a lot of information on each pic to take the correct conection more easy :mrgreen: Where is the correct place to conect this plugs? Blue circle: 3 5 Red circle: 6 7 and 1, 2, 4??? :o: http://img140.imageshack.us/img140/997/img0660n.jpg http://img35.imageshack.us/img35/7849/img0661yjy.jpg htt...

appletree wrote:Nice work, not short of engine hoists i see

Sorry, but I don't understand you

I bought this M/C without servo

to this guy

http://www.r3vlimited.com/board/member.php?u=11468

This is the M/C I used in my swap

Pic of today

Now I'm trying to finishing the wiring

Amazing

Search found 35 matches

Re:

Re:

Re:

Re:

Re:

Re:

Re: another s50 the easy way round !

Re: another s50 the easy way round !

Re:

Re:

Re:

Re:

Re: another s50 the easy way round !

Re: Coding Plug Mod E30M3

Re: another s50 the easy way round !

Re: M50/M52/S50 swap, 944 servo question?

Re: s50 trottle cable

Re: s50 trottle cable

Re:

Re:

Re:

E30 M3 + S50B30

Re: