E30 Zone

Looking for a drivers door and passenger rear quarter door mouldings please.

Need coupe passenger rear quarter and drivers door pls.

Which part is it you need? Do you have a picture?

32106891974 price and availability please.

Thanks

Looking for a good e36 320/325 power steering pump .

Prices and availability pls

61621381525
61621381845

Anyone help ? Pin 1-black wire-5volt in Pin 2-shielded wire-ground Pin 3-yellow wire-signal out Pin 4-ground Pin 5-WOT switch Pin 6-Closed switch If you look down past the pins with a torch you can see the pin numbers at the base of the pins. Thank you that makes sense the car was auto many moons a...

Looking for a touring rear wiper arm if anyone has one .

My idle is a bit low (600) and its sometimes cutting out on the down shift 4th to 2nd . It seems to happen on when at operating temp . Cars a m20b25 with lightened flywheel. I have tested the blue sensor 4.36 kohms cold at both ecu and sensor and .375 kohms hot at sensor and ecu . I don't seem to ha...

Still getting the brakes binding after pressing the pedal with the car running . Brake pedal just not returning enough about 25mm short. If I stick my toes under the pedal and lift it up the 25mm the brakes free and the brakes light switch works until the next time i press the pedal . Running out of...

DanThe wrote: ↑
Sun Nov 27, 2022 3:25 pm
Yes, the pull bar at the back of the servo should be disconnected too when checking this

Thanks Dan i will check it out .

Adjusting pedal height is the last process before setting brake light switch position You need to ensure the servo pushrod is set to the correct position relative to the master cylinder before even fitting them to the car. On E30 servos the pushrod is usually flush with the face of the servo Sorry ...

Today i have fitted the new brake switch , released the pin from the servo side ,adjusted the brake pedal to be inline with the clutch pedal , adjusted the servo end and refitted the pin . Still got the problem of the brakes locking on after i press the pedal. if i lift the pedal with my foot the re...

Thanks guys . I did disconnect the pin from the push rod side the other week while trying to source the issue and i did have to align the holes to get the pin back in . I will adjust the servo end fit a new brake switch adjust the bar across to suit and cross my fingers .

Looks like the bar/ master cylinder bar have been adjusted at some point , If i back the bar running from the pass side to the drivers off the front brakes don't bind (still a wee bit drag but not excessive imho) Question now is is there a way to do a factor reset on the brake adjustment bars/rods? ...

Been having a look at this . If I disconnect the hose off the servo I can blow into the engine put can't suck which I think is right and the check valve is working . If I apply the brake with the hose off (car jacked up )the brakes work and release ok . If I connect the hose with the engine running ...

I did clean and grease the sliders also pushed the pistons out as far as i would dare and they are free of rust .I will try pulling the hose off to the servo .

I saw the calipers on autodoc and have them sitting in the basket just incase .

Thanks for the replies .

Got an mot failure for brakes binding and brake lights staying on .(car had sat for about 4 years so no surprise ) So i stripped the calipers ,checked the slider ,pistons coming out and going in with no corrosion on the bits that matter as far i as i can see.Put back together wheels spinning free. A...

Payment set via paypal

Thanks

32106891974 repair kit
83238849305 grease

Thanks

Satan wrote: ↑
Sat Mar 27, 2021 11:51 am
Are these the ones that swallow the swirl flaps?

Not that i have read . They do seem to have issues with timing chains going slack .

I bought a F31 (touring) 330d around 6 months ago and its been a great car so far. It's my first diesel but I think the engine is great and just keeps pulling. The engine noise from in the cabin sounds pretty good IMO, I test drove the 320d as well and that sounded like a tractor. The 330d is much ...

Good mate of mine had 330d and then 330i. That straight six diesel was a weapon with the torque it had. 330i was probably faster but for double the consumption. One thing he never got on with was the ride, rock hard on both. For me I own nothing BMW newer than 2004 :D . Nothing they have done since...

Anyone running one of these and what engine/experience have you had ? Keep reading stories of failed timing chains on the 320d and i was thinking on the 330d which is more or less the same engine for what i can see . Wondering if i should go for a petrol engine ( only reason i'm thinking 330d is the...

TriggerFish wrote: ↑
Sun Feb 21, 2021 1:44 pm
Appreciate this is an older question, but I got these: https://www.ebay.co.uk/itm/Brake-Line-T ... 1631059542

I couldn't find them domestically

Ended up ordering the same .

Really like that and need more pictures.

Wee tidy up in the bay and a wipe down of the plastics .

BenHar wrote: ↑
Sat Jan 23, 2021 8:45 pm
Electric fan?

Is that an original fitment?

Ben

No Ben it had been fitted as part of the engine swap.

Fixed the issue with this today so thought i would update this just incase someone every has this . After pulling relays and fuses i found it was either a problem with the loom from the fusebox to the head lights or the loom for the fusebox to the electric fan . I rechecked every plug,the fan loom c...

There shouldn't be much of a problem adding the oil sensor wires to an E36 loom, especially if you already have a plug that fits the sensor, but is the E38 oil sensor compatible. At some point BMW moved away from a simple float switch arrangement, and moved to a weird system based on (IIRC) thermal...

What engine is the E38 sensor from and what engine is the E36 loom? The fact the earth wire in the E36 plug is in pin 1 makes me wonder if it is actually the oil level sensor plug? as they are usually pin 2 Here is an M50 sensor diagram next to an E30 M20 diagram The pin numbers on the plug have th...

That gauge is a 63 litre version, if the drivers side sensor wire is trapped/damaged and shorting to earth this would give a faulty fuel level of exactly 1 half when the other side of the tank is empty (as you have confirmed) The low level warning signal wire is also on the drivers side When you fi...

ignition on, but engine not running, handbrake on, headlamp switch on and fog light switch off

blue plug out = n/s indicator warning light
white plug out = o/s indicator waring light
yellow plug out both indicator waring lights

white plug out white plug out.jpg yellow plug out yellow plug out.jpg blue plug out blue plug out.jpg Spare cluster same coding plug spare cluster same coding plug.jpg Low fuel light was due to low fuel as it ran out today . 20l can was still sitting there full sorry (old age is obviously getting to...

Brianmoooore wrote: ↑
Thu Jan 14, 2021 9:27 pm
Yes, try the spare one. All info. helps in working out this weird one.
Since you have an OBC, test with the yellow plug disconnected as well. It will be even weirder if this makes a difference, but it's more data.

Will do Brian thanks.

Search found 3314 matches

Coupe door moulding

Door moulding

Re: M20 Rocker shaft retaining plate dimensions.

Price please

E36 m50 power steering pump

wiper arm

Re: Low idle

touring rear wiper arm

Low idle

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

Re: front brakes binding

front brakes binding

Re: prices please

prices please

Re: Thinking of buying a f30

Re: Thinking of buying a f30

Re: Thinking of buying a f30

Thinking of buying a f30

Re: Rx7 inverted flare to bubble flare

Re: I made it official

Re: Coupe reshell

Re: weird cluster and light issue

Re: weird cluster and light issue

Re: e38 to e36 oil level plug

Re: e38 to e36 oil level plug

Re: weird cluster and light issue

Re: weird cluster and light issue

Re: weird cluster and light issue

Re: weird cluster and light issue