Delaneys Brilliant Red 318i - Partial Restoration

Show off your pride and joy here
Post Reply
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Wed Nov 28, 2018 5:21 pm

Well, I must say it's good to be back! Hope I haven't missed much!

In January 2016, I stupidly sold my beloved Alpine White 316i that I had poured countless hours and euro into to get it to the car it was. I was young, short on cash and the car just didnt make sense to daily, so it was sold for an economical E90 320D.

Image

Over the next few years I was reminded by the lads and by photos on my phone of the car and began to regret masssively what I had done.

Having graduated earlier in the year and nailed down a good, well paid, job, I began my hunt for the perfect E30 once again.

Spotted her at 2am on Monday on a facebook 'e30 buy/sell' group of all places. Knew instantly I was on to something good just from looking at the photos.

After a lengthy chat and more photos, I agreed a deposit and secured the car. Shes currently located in the south of England, all being well, I'll get her on the drive in Dublin next weekend.

Here it is:

Image Image

Image Image

Image Image

Image Image

Late 1989 manual M40B18 in brilliant red with all the right parts fitted.

- MTech2- Genuine polyurethane Kit
- 51 mm strut upgrade
- Rear disc Conversion
- LSD
- BMW Purple Tag Steering Rack
- M3 Petrol Tank Running Twin Pumps
- Installed Battery Tray In Boot
- Scorpion back box
- Electric Mirrors and Windows
- MTech2 Steering Wheel
- Sunroof
- Houndstooth sport interior
- Rear sun blind
- Lowered 40mm on Apex Shocks and Springs

Bodywork wise she was stripped to the metal and all welding done including new inner and outer arches in 2013. The engine was pulled and reconditioned while it was sprayed.

I'll likely strip down the head in the new year and do the cam shaft and all related components. Other than that, the engine has got everything it ever needed and is running very smooth and quiet.

All the original paperwork and books are with the car with reems of papers from previous owners.

So I flew out at 6am on the Saturday morning flight to Gatwick and took the train down to the south coast of England to get her. Embarked on the 380 mile journey back home. She did it all on €80 fuel which suprised me massively. I also own a MK5 Golf GTI as my daily and it's nowhere near as economical on a long run!

Never skipped a beat the whole way home. Was delighted. Learned alot about the car on the journey and the little niggles and issues it has that I'm looking forward to fixing.

Image

Drove her into the drive at home and the father came out to have a look. Sat in, started her and took it up the road. A whining noise started and began to get louder and louder until the temp needle started to creep up and the battery light came on. Pulled in and she had thrown the alternator belt!

I'm a very lucky man to have made it home just minutes before without this happening sooner, leaving me stranded.

Got two new belts on Monday and pulled it into the garage to fit them and have a closer look underneath.

Image

It's quite corroded underneath but nothing a clean up won't fix. The perks of living beside the coast :( I will replace parts like tie-rods and wishbones just to freshen it up. Going to pull apart the front calipers and hubs and clean everything up too.

Hopefully get some photos up soon.

First though, I'll bend over for Irelands absolute shafting of vehicle registration, tax and insurance before I settle into any major work.

Here is some more arty photos for those interested that I took last weekend

Image Image Image Image

Image Image Image

Image Image Image

Image Image
Thanks for looking, this one is a keeper so expect many more posts!

Ross
Last edited by DelaneyE30 on Wed Jan 09, 2019 6:45 pm, edited 1 time in total.
Image
shedrool83
Old Skooler
Old Skooler
Posts: 4237
Joined: Thu May 10, 2007 10:00 pm
Location: Dundee Scotland

Wed Nov 28, 2018 7:23 pm

My first e30 was a red m-tech 2 325i se and looking at yours brought back same good memories .Yours looks stunning, a mint red tech 2 is hard to beat imo.
Image
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Fri Nov 30, 2018 12:11 am

You very very lucky boy :clap: :clap: :clap:

These dont come up on a regular basis and I hope you hang on to this one .lol winkeye winkeye winkeye
Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
User avatar
Steve
E30 Zone Team Member
E30 Zone Team Member
Posts: 12852
Joined: Sun Dec 19, 2004 11:00 pm
Contact:

Fri Nov 30, 2018 10:33 am

Great, thanks for sharing and keep the updates coming. :thumb:
webmaster@e30zone.net
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Fri Nov 30, 2018 10:57 am

shedrool83 wrote:
Wed Nov 28, 2018 7:23 pm
My first e30 was a red m-tech 2 325i se and looking at yours brought back same good memories .Yours looks stunning, a mint red tech 2 is hard to beat imo.
martauto wrote:
Fri Nov 30, 2018 12:11 am
You very very lucky boy :clap: :clap: :clap:

These dont come up on a regular basis and I hope you hang on to this one .lol winkeye winkeye winkeye
Mart.
Steve wrote:
Fri Nov 30, 2018 10:33 am
Great, thanks for sharing and keep the updates coming. :thumb:
Thanks all. Looking forward to getting stuck into this project over the next few months. I'll keep it updated!

And no, this one isn't getting sold anytime soon! :D
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Mon Dec 03, 2018 1:08 pm

01.12.18 Update

Began ironing out the little niggles and issues the car has on Saturday.

Removed the drivers seat to fix the play in the frame. The mechanism to adjust the seat up or down is very loose so the plan is to drill out the rivets holding this together and fit a nut and bolt instead. Should tighten things up. While the seat was apart I cleaned and painted the rails. Didn't spend too much time on this as these seats will be getting trimmed later in the year with new houndstooth cloth.

Image Image Image

My air vents were very loose so I removed them, cleaned them and re-fitted them with rubber washers to tighten up the looseness.

Image Image

This next little bit of attention to detail was something I did on my previous E30 too. Removed the cluster to check the connections and replace two blown bulbs. Removed the little plastic blanking plate where the 'check engine' light would be on some cars. Printed off a little ///M badge and glued it to the plate. Simple but cool mod!

Image Image

Finally, I have this strange issue where the drivers side headlight comes on with the sidelights. I removed the relay, tested it on the bench and it works fine. Removed the switch and stripped it to clean up every connection. Still the problem persists. Next step is to check the earths and see if there is any poor contacts there. While I had the switch out, I fitted some blown bulbs too.

Image

More to come as always!
Image
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Mon Dec 03, 2018 3:30 pm

The devil is always in the detail and there is no lack of it here :banana: :banana: :banana:
Love the "M " idea :cool:

Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
rix313
E30 Zone Addict
E30 Zone Addict
Posts: 3919
Joined: Fri Oct 31, 2008 11:00 pm
Location: Silverstone / Westbury, Wilts
Contact:

Thu Dec 13, 2018 10:15 am

I wish i had the patience to do what you're doing. It looks stunning.
E30 318iS 'Winston' race car: viewtopic.php?f=88&t=212937

E30 318iS 'Poppy': viewtopic.php?f=25&t=200349

E30 318iS 'Emily': viewtopic.php?f=112&t=277288
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Fri Dec 14, 2018 7:46 pm

rix313 wrote:
Thu Dec 13, 2018 10:15 am
I wish i had the patience to do what you're doing. It looks stunning.
You only need a bit of age mate. :cool: :cool:

Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Wed Jan 02, 2019 10:55 am

Big update!

Christmas break has been good to me in terms of progress on the car. Managed to convince the father to move his MK2 Escort out of the garage into our storage unit. Got the E30 in and decided to strip it. Bit of a rash decision, but worth it none the less.

Out came the seats and carpets. These will be valeted before re-fitting.

Image Image

Underneath, the floors were solid with a few spots of surface rust. Over the next few days I sanded these back, treated them and sprayed on fresh paint.

Began stripping the front and rear subframe starting with the calipers. These are quite badly corroded so I split them down and ordered up new seals, pots and bleed nipples. The calipers and carriers have been sent off for sand blasting.

Image Image Image

Removed the aluminium rings that surround the lights, sanded them back and treated them to a fresh lick of paint. Simple yet effective touch.

Image Image Image

Stripped more from the front of the car. Put in a big order on ECP for a load of new parts.

- control arms
- droplinks
- control arm bushings (powerflex)
- tie-rods
- new discs, pads, hb shoes and sensors all round

Sent the subframe off for blasting with the calipers. This will then be painted black. Stripped out the brake servo and master cylinder too.

Image Image Image Image

Image Image

Began sanding and painting all these parts. After two days covered in dust, I had some nice shiney parts ready to bolt back on.

Image Image Image Image Image

Also got a roll of zinc brake line and fittings along with rubber pipes for all four corners. Began bending and swaging the lines. Front end is finished, just the rear left to do.

Image Image Image Image

As always, lots more to do but happy with progress so far.
Image
rix313
E30 Zone Addict
E30 Zone Addict
Posts: 3919
Joined: Fri Oct 31, 2008 11:00 pm
Location: Silverstone / Westbury, Wilts
Contact:

Wed Jan 02, 2019 2:22 pm

Lush.
E30 318iS 'Winston' race car: viewtopic.php?f=88&t=212937

E30 318iS 'Poppy': viewtopic.php?f=25&t=200349

E30 318iS 'Emily': viewtopic.php?f=112&t=277288
User avatar
Steve
E30 Zone Team Member
E30 Zone Team Member
Posts: 12852
Joined: Sun Dec 19, 2004 11:00 pm
Contact:

Thu Jan 03, 2019 9:04 am

Great update, loving that ramp. :thumb:
webmaster@e30zone.net
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Fri Jan 04, 2019 12:59 pm

Steve wrote:
Thu Jan 03, 2019 9:04 am
Great update, loving that ramp. :thumb:
:cool: :cool: :cool: :cool: :cool: :cool:

Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Fri Jan 04, 2019 5:16 pm

rix313 wrote:
Wed Jan 02, 2019 2:22 pm
Lush.
Steve wrote:
Thu Jan 03, 2019 9:04 am
Great update, loving that ramp. :thumb:
martauto wrote:
Fri Jan 04, 2019 12:59 pm
Steve wrote:
Thu Jan 03, 2019 9:04 am
Great update, loving that ramp. :thumb:
:cool: :cool: :cool: :cool: :cool: :cool:

Mart.

Thanks all!
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Wed Jan 09, 2019 6:45 pm

Another weekly update!

Postman arrived with a big box of new parts from ECP. Everything to refresh the full braking system and front suspension arms etc. Can't wait to get this all fitted soon.

Image

Began stripping the top end of the engine to replace and clean-up parts. Tore down the rocker cover, inlet mani and timing belt housing to send these off for blasting. The camshaft is good with no pitting on the cams/followers. It had previously been replaced anyway. All the rubber fuel and water hoses were badly perished so I removed these to replace with new items. Timing is good but there is some marginal slack in the belt so I'm going to change this and replace every seal, o-ring and gasket. Water pump and viscous coupling have been previously replaced.

Image Image

Got the cross member and calipers back from blasting. Immediatly sprayed the calipers with metallic grey heat resistant paint to avoid corrosion. I have new seals and pots for these on order. Got the spray gun out and gave the cross member several coats of black. Also sprayed the spare wheel while I was at it.

Image Image

Image Image

I began piecing the rear end back together last Saturday. Coated the rear panel and boot floor in Gtechniq sealant. Waxoyl'd both pockets and every cavity I could find to protect it. I cleaned the carpet boot trims and re-installed. New Hella number plate lights were fitted as were the taillights with fresh silicone sealant.

Image Image Image

New parts are always fun to recieve and the postman treated me well on Monday and Tuesday of this week.

Image Image Image

Got the engine parts back from blasting. Beautiful, raw aluminium finish. You would mistake them for being painted silver. I'm going to lacquer these to preserve the finish.

Finally, I removed and restored the starter motor. I also re-fitted the brake servo/booster and temporarily connected the lines to ensure fit.

Image Image

To summarise, all new parts purchased so far:

- wishbones x2
- disc x4
- pads x4
- calipers (restored) x4
- wishbone mounts x2
- polybushes up front x2
- droplinks
- front ARB and components (restored)
- inner & outer tie-rods x2
- tie-rod boots x2
- top end gasket / seal kit
- timing belt
- belt tensioner
- fuel & oil filter
- all brake lines replaced (rubber and hardlines)
- all fuel lines replaced (at tank and in engine bay)
- restored throttle body
- restored brake servo
- restored brake booster
- restored starter motor

Lots done and as always, lots more to do. Once everything that is currently stripped has been replaced or restored, I will then begin on the rear subframe / suspension.
Image
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Thu Jan 10, 2019 3:31 pm

How on earth can this be a Partial ????????? :cool: :cool:
If only.lol

Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Thu Jan 10, 2019 4:26 pm

martauto wrote:
Thu Jan 10, 2019 3:31 pm
How on earth can this be a Partial ????????? :cool: :cool:
If only.lol

Mart.
Hahaha my OCD wishes I had the time, space and funds to strip this to a bare shell and start over. To me, that's a full resto :D
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Wed Jan 16, 2019 4:43 pm

Wednesday Update

Not much photographed progress this week. Was at Autosport International so the weekend was lost for any progress on the car.

Stripped the head to change the valve stem seals. Time consuming job removing and re-fitting the collets while keeping the springs compressed. Its done and the engine is timed. Should run much smoother now.

The caliper rebuild kits arrived. Once the engine work is complete I'll start into rebuilding the braking system.

On a sidenote, I've ordered a full Powerflex rear bushing kit and new NGK plugs too. I also picked up a spare set of 51mm struts to use the knuckles for new coilovers.

Image Image

Image Image

Its slowly getting there now. Looking forward to having this one on the road.
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Thu Jan 24, 2019 5:21 pm

Weekly Update.

M40B18 refresh complete.

The key to a good looking BMW is a clean, painted rocker cover. Gave mine a blast of the wire wheel and then covered it in numerous coats of textured satin black paint. As it was setting, I got a blade and scraped the paint back off the lettering and lines. Using some emery, I polished this to a shine. Simple but perfect look.

Began putting the head back together with new gaskets and seals all round. A new timing belt was fitted along with a new seal on the temp sensor. Removed the crusty exhaust manifold gasket and replaced it with a new one which incorporates a alloy heat shield. Looks well.

Image Image Image

I replaced all fuel and water hoses with new genuine BMW items. The fuel rail was cleaned and fitted with new o-rings on the injectors. I cleaned out the throttle body and ensured working condition and re-fitted with new gaskets.

Image Image Image

Image Image Image

That’s the engine bay almost complete. Have to sort a lagging wiper motor before I can piece the firewall trim back together.

On to the front chassis / subframe.

This area of the car has come together lovely. If I had the time and money I'd have stripped it back to bare metal and remove the body seal on the inner wings. Wish these were red (like original) but as for the sealer, they had to stay black. The car is getting a set of BC Racing coilovers, so i did not replace the wheel bearings or dust shields until the coilovers have been welded to my 51mm knuckles.

Image Image Image

I got some rubber grommets at the Autosport Show and fed my new brake hardlines through them with new retainers from BMW. Re-built the calipers with new pots and seals and fitted them temporarily to the struts.

Image Image Image

Cleaned up a few other small bits like this bracket and fitted new NGK plugs. The post-man arrived with a Powerflex rear bushing kit which I've added to the box of parts for the rear end.

Image Image Image

Can’t wait to get it outside for some proper photos. These don’t do it justice at all. Very happy with how the car is turning out. Rear end restore next!
Image
User avatar
pierce
E30 Zone Newbie
E30 Zone Newbie
Posts: 198
Joined: Sat May 30, 2015 10:00 pm

Thu Jan 31, 2019 4:42 pm

Stunning!

Thanks for sharing and for the regular updates!

Quality of work is brilliant, and the photo quality is amazing!

The autumn photos in your first post are lush! Did you take these yourself? What camera / lens are you using?
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Sat Feb 02, 2019 12:07 pm

pierce wrote:
Thu Jan 31, 2019 4:42 pm
Stunning!

Thanks for sharing and for the regular updates!

Quality of work is brilliant, and the photo quality is amazing!

The autumn photos in your first post are lush! Did you take these yourself? What camera / lens are you using?
Thank-you! I work in digital media so I've become familier with the old photography :D Those images were shot on Sony a7iii and Zeiss 50mm f/1.8!
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Mon Feb 11, 2019 12:16 pm

Rear chassis refresh update.

With the front end almost complete, focus has turned to the rear end of the car.

Image Image Image

I dropped the rear beam, diff and trailing arms. These were heavily weathered with 30 years of driving on English roads so the decision was easily made to have them sand blasted.

Image Image Image

I removed some of the heat shielding and with the help of the pressure washer and some tar remover, this cleaned up well. I also hit the LSD with the grinder to try clean up the majority of the corrosion on the case. As I do not intend to split the diff (it's tight and working fine), I will not be blasting the main casing, just the cover. I picked up a litre of Castrol Syntrax 75W140 to replace the oil with.

Since purchasing the car, I only had one set of wheels in mind for it. OEM+ style 16" BBS RZ469. Managed to source this set close to home in decent condition for their age. I'll probably get these refurbed and powder coated silver with red BBS caps to match. I'll mount these to some sticky 195/45 rubber.

Image Image Image

Along with collecting and cleaning up new/old parts, I gave the rear chassis some love. Sanded back the flaking body seal and removed every patch of corrosion and rust I could find. Treated the bare metal and then seam sealed everything. Once dry I coated the whole underside in a layer of body schultz. Not ideal but it will protect the car until I strip it to the bare metal in a few years time.

Image Image Image

With the M3 tank out, I tested both pumps and replaced all the rubber hoses with new Gates fuel pipe. Then began burning the bushings out of the rear beam and trailing arms.

Image Image Image

Spare 51mm stub axles cut awaiting blasting along with diff cover, trailing arms, beam and brackets, dust shields, exhaust brackets and sump. I have ordered a set of BC Racing coilovers with 8kg spring weights to weld the stub axles to. New MOOG wheel bearings are also on order.

Image Image

Finally, a little surprise awaited when I dropped the sump. Initially I hadnt planned on dropping it but now I am glad I did. Previous owner had siliconed the sump to try seal it. The engine obviously sucked the silicone into the oil pickup, almost blocking it. Very lucky to have found this. Sidenote: Ignore the state of the purple tag in this photo, i'll treat it to a lick of silver paint.

More to come as always. The end is near!
Image
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Tue Feb 19, 2019 11:21 am

Rear chassis refresh continued...

BC Racing coilovers arrived. I had researched a number of options before settling on these. I didn't want to run a shock/spring kit as these greatly hinder adjustment and lowering. I looked into Ground Controls setup and KW varient3's however these are going on a 120hp 1.8 that will likely never see the track so it didn't make sense to sink so much cash into motorsport orientated suspension. The build quality of the BC's is impressive. Theyre finished in a thick powder coated layer of black with anodised adjustable top mounts in BC's signature gold. They offer the best lowering, quality and adjustment for the money so it was the obvious choice in the end.

Image Image Image Image Image

During the week I picked up the rear chassis components from sand blasting. These came out beautifully aside from two minute holes in the fuel filler neck. I soldered these up and brazed a new outlet for the evap pipe.

Image Image Image

Image Image Image

Began fitting the brake hardlines we had made previously. Nothing better than assembling new parts compared with the crust and corrosion that was present before. Welded the lower sleeves off the coilovers to the stub axles too. Fairly simple job that involved cutting the strut tower 50mm up from the stub axle and then welding a sleeve over the remaining portion of the strut tower. The coilover then screws into this sleeve.

Image Image Image

Over the weekend we setup a miniature spray booth and hit every part that needed paint with a thick coat of satin black. Setup the money shot of the rear axle components on the utility room floor much to the annoyance of the parents! :D Aside from a few brake line clips and brackets for heat shielding, thats pretty much every part for the rear end. While I was messing around at this, the father had re-assembled the fuel system in the drivers side rear arch. New rubber filler neck seal, new piping and new filler cap.

Image

Image Image Image
Image Image Image

Finally to top off a busy weekend we rebuilt the diff with new oil, bolts and washers. Although the casing is heavily pitted, I'm very pleased with how this came out.

Image Image

Nearing the end of this project now. 2 more weeks and it'll be on the road I'd say. If you've made it this far and have bothered to read through my waffle, thank you. :)
Image
User avatar
Gert
E30 Zone Newbie
E30 Zone Newbie
Posts: 21
Joined: Mon Jul 13, 2015 10:00 pm
Location: Limburg (BE)

Tue Feb 19, 2019 11:58 am

Nice restauration! Great photos. Keep going
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Tue Feb 19, 2019 1:05 pm

Gert wrote:
Tue Feb 19, 2019 11:58 am
Nice restauration! Great photos. Keep going
Thank you!
Image
User avatar
martauto
E30 Zone Team Member
E30 Zone Team Member
Posts: 2949
Joined: Wed Aug 31, 2005 10:00 pm
Location: leeds

Tue Feb 19, 2019 2:49 pm

I love to see things like this and it has not let me down one tiny bit. :clap: :clap: :clap:

Wish I had the space for something as good as this. :cool: :cool:

Mart.
E30 316 coupe 1986 (rip)
E30 316 Baur 1987 (Feeling sorry in the drive but alive !!)
E36 318ti Sport (rip)
E46 330 Ci SE (rip)
E46 330 Ci Sport
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Tue Feb 19, 2019 3:26 pm

martauto wrote:
Tue Feb 19, 2019 2:49 pm
I love to see things like this and it has not let me down one tiny bit. :clap: :clap: :clap:

Wish I had the space for something as good as this. :cool: :cool:

Mart.
Thanks! Our garage isn't the largest either but it'll do.
Image
User avatar
TurtleDesignTech
E30 Zone Newbie
E30 Zone Newbie
Posts: 120
Joined: Tue Sep 15, 2015 10:00 pm
Location: Hampshire

Wed Feb 20, 2019 7:35 pm

Thanks for an epic 30 minute read.

What did you do with the intake manifold in the end. Is it really just sandblasted and lacquered?
User avatar
DelaneyE30
E30 Zone Newbie
E30 Zone Newbie
Posts: 22
Joined: Sun Sep 27, 2015 10:00 pm
Location: Dublin, IRL
Contact:

Thu Feb 21, 2019 2:35 pm

TurtleDesignTech wrote:
Wed Feb 20, 2019 7:35 pm
Thanks for an epic 30 minute read.

What did you do with the intake manifold in the end. Is it really just sandblasted and lacquered?
Thanks! Yes, thats bead blasted and then lacquered over. Came out very well, very please with it.
Image
Post Reply