E30 Zone

I need to take my front and back seats out of my 2 door.........anyone got brief instructions on how to do it? What tools will I need?

Pi$$ easy.

Front seats - 4x nuts / bolts per seat. Just slide it forward to get to the back ones & then backward for the fronts.

Back seats - base is probably just clips at either side - just pull upwards. Very early cars had 2x screws that are really obvious.

The seat back'll have a couple of bolts at the bottom that you can see once the seat base is out, it then pulls straight upwards off of a couple of hooks. Should take you no more than about 10 mins all in!

Tools - 13,15,17mm sockets (can't remember what size they are!), & perhaps a screwdriver.

1x ratchet
1x 17mm socket
1 x extension bar

as said 2 nuts and 2 bolts per front seat

2 minute job per seat

mind ya paint when draggin em out of the car

Front: 17 mm socket and a ratchet on all 4 bolts which fix the seat to the floor, then 17mm socket on the seat belt attachment..

rear: Pull the bottom section upwards to remove, then remove the two 10mm screws at the the base of the seat (at bottom corners), and push the seat back upwards.

easy as pie.

why you taking it out though,,


the back part is structural so dont drive without them

the back part is structural so dont drive without them

You what? back seats aren't structural mate, nor are the fronts - useful features though!!

Slightly off topic but could someone tell me what size the nuts and bolts are for the front seat?

I'd like to add a pax seat in my track car but don't have the original bolts.

Thanks
Ianmeister

Ianmeister wrote:Slightly off topic but could someone tell me what size the nuts and bolts are for the front seat?

I'd like to add a pax seat in my track car but don't have the original bolts.

Thanks
Ianmeister

erm...17mm

Ianmeister wrote:Slightly off topic but could someone tell me what size the nuts and bolts are for the front seat?

I'd like to add a pax seat in my track car but don't have the original bolts.

Thanks
Ianmeister

I think they're M10 off the top of my head. PM me your address & I'll post you a set.

Cheers,
Chris

smithy318i wrote: then 17mm socket on the seat belt attachment..

Someone is used to 4 doors!

ad318i wrote:
the back part is structural so dont drive without them

Theo325 wrote:

the back part is structural so dont drive without them

You what? back seats aren't structural mate, nor are the fronts - useful features though!!

If my back seat was holding my car together i woulnt take it over 5mph! The only other thing they do other than provide seating and a bed is keep out some of the noise.

bigpimpin wrote:

ad318i wrote:
the back part is structural so dont drive without them

And if you fold it flat, it weighs less.

Chris-W wrote:

bigpimpin wrote:

ad318i wrote:
the back part is structural so dont drive without them

And if you fold it flat, it weighs less.

hubby took my rear seats and carpet out for a spot of welding it needed for the MOT.... that was about 3 weeks ago, its damn noisy without them!


definately not structural or I wouldnt drive the car with my baby in it.

dobbie82 wrote:hubby took my rear seats and carpet out for a spot of welding it needed for the MOT.... that was about 3 weeks ago, its damn noisy without them!


definately not structural or I wouldnt drive the car with my baby in it.

Yer the noise is hugely different. I drove my car (stupidly) without anything in it all at except for front seats, gear knob, and the dash, which was half balanced in place. It was SOO much louder. Realy fun actually

Paul

Sorta off-topic: how do you remove the panel on the back side of 2-door sport seats? I thought it'd be easy. Are there concealed screws somewhere?

erm...17mm

he he he thats the size of the hex head not the bolt

any yes M10 it is (which is actually 10mm )

as for the rear panels, remove seats front and rear as mentioned, remove door rubber strip, remove the plastic sill covers, remove the seat belt cover and lower belt. then from memory should come out by pulling and lifting, but have a look down at the botom near the rear seat base may be a screw there.

mrlee

KDS wrote:Sorta off-topic: how do you remove the panel on the back side of 2-door sport seats? I thought it'd be easy. Are there concealed screws somewhere?

Two small brass screws at the bottom. Tilt them forwad and you sill see them. Then yank off the tilt handles and slide the seat back upwards. DONT just pull it off!!

Paul

bmwe30mtech wrote: provide seating and a bed

a bed eh!?

if paul can do it,, anyone can

- Gota luve the zone! All of us are ex-famous comedians!! But the seats do weigh less when you fold em!! - I've just taken my interior out for the first time for wiring and was very supprised to hear the difference in noise levels!! Glad to say it didnt fall apart though!!

dark_sounds wrote:

bmwe30mtech wrote: provide seating and a bed

a bed eh!?

if paul can do it,, anyone can

Oy Ali! Thats uncalled for lol. I will be having words next time i see you and the girly lol.

bah!

what words, u know its right

Thanks guys....got them out in about 5 mins. Didn't realize it was so easy!

New recaros have gone in....will post up pics on Sunday.