Page 1 of 1
BBS RS offset
Posted: Tue Feb 28, 2006 9:52 pm
by NICKE30CAB
quick question is it possible and what offset is required to fit 8x16 front and 9x16 rear bbs rs wheels to a e30 with m3 suspension/hubs etc on it.
cheers
Posted: Tue Feb 28, 2006 9:54 pm
by bigpimpin
I want to know exactly the same !
only I was thinking 17".
Posted: Tue Feb 28, 2006 10:57 pm
by NICKE30CAB
gorgeous arent they i have run 17"s for a while now but find the ride abit harsh so im going back to 16"s
Posted: Wed Mar 01, 2006 1:22 pm
by NICKE30CAB
some one must know?
Posted: Wed Mar 01, 2006 7:20 pm
by bigpimpin
Yeah, someone must have these fitted! If not in the UK some of the overseas zoners????
Posted: Thu Mar 02, 2006 9:14 pm
by NICKE30CAB
hi
Posted: Fri Mar 03, 2006 1:49 am
by eun
nav is usually quite good with knowing wheels etc
Posted: Fri Mar 03, 2006 7:52 pm
by Simon13
no one knows because no one has bbs rs in 16inch as they are so rare!
i know the answers for u for bbs rs in 15's with 7j fronts and 8j rears!
Posted: Fri Mar 03, 2006 8:21 pm
by NICKE30CAB
not so rare i 5 stud fitment though
Posted: Tue Mar 07, 2006 4:09 pm
by bigpimpin
OK so NOBODY has BBS RS Split rims on an E30 with M3 5 stud setup??
Looks like we may be the first !
I'm gonna measure the distances between the stock E30 hubs and the M3 ones when I fit them. Then we should be able to work out what offsets would fit.
There's a cracking set of 16" ACTs on ebay just now, 5 stud, 8.5 x 16" ET11. I'm pretty sure these would fit the standard e30 arches but it's a lot of money to lay out if they dont !!
surely someone out there can help?
Posted: Tue Mar 07, 2006 9:51 pm
by NICKE30CAB
yeah ive seen those nice arent they
try this bigpimpin
http://www.s14.net/forums/showthread.ph ... adid=17852
Posted: Sun Apr 02, 2006 9:52 am
by bigpimpin
Posted: Sun Apr 02, 2006 10:07 am
by nikos
I got it from a forum long time ago and I saved it to use it when I go bigger. I hope it helps:
Sorry for the hi-jack but i didn't want to start a similar thread.
I just inherited a 1991 325i cabrio. i really want the look of the new m3 rims.
i found some rims that are pretty darn close. they are the alessio plus. the problem i am gettin is that most places tell me the offset is not correct. the rims are 17 x 7.5. 4 lug x 100mm. so what do i need to do to make these work? just a spacer? i saw this in a similar thread posted by
an318is
"Offset depends on what width rim you want the following is a good guide
6" rim width: 35mm offset
6Âa" rim width: 30mm offset
7" rim width: 25mm offset
8" rim width: 15mm
the stud pattern as mention above is 4x100 and the centerbore is 57.1mm Thats pretty important as the weight of you car will be supported on the rim of the centre hole, not the wheel nuts"
so if i understand this correctly i just need to buy or fabricate a spacer that is 20mm thick? tia!
