E30 Zone

will this replace the other?

Anyone know what starter motor was fitted to the earlier Alpina c2 2.7? (KW/ Number of teeth) Thanks

Just swapped them, no difference..

stays on constant. I have checked all 4 sensors and there giving a variable Ohm reading when the wheel is being spun. Its pre facelift so checked the fuse wire in the silver relay next to the ecu. I Broke A E30 that had a fully working ABS and kept all the bits from it.. so used the ECU of that and ...

Hi, ABS has never worked on my car since ownership, checked sensors and the relay, even swapped the ecu for a known working one. still not resolved. The Break pedal has always been hard to depress, much harder than other E30's that I have owned and reading on other forums this can be also be related...

I got extra air horns fitted to mine as i thought the original twin horns sounded a bit week. I did have a Dixie horn fitted on a previous car.

was a good laff sounding it when over taking someone ( I Know Big kid )

worst i had was in the winter on a strait duel carage must have hit black ice.... i just accelerated slowly lsd kicked in and sent me through a 360 still traveling forward at 50 mph

I got the car strait but don't know who had the more shocked look on his face me or the guy following

my 2:7 alpina has a 3.9 LSD accelerates like a scalsis cat 33mpg on a run 0-60 just under 6 seconds 1st gear is short but not 2 short. Leave it in 2nd in trafic

Thanks guys. It was only flaying for a matter of seconds. left the car there and got it towed 1/2 mile to the oldie's house. Prop was a tight fit when I pushed it back in. Only needed to replace 3 of the bolts as the other 3 were still intact (guess they did not undo these) 3 new bolts locktighted i...

thanks guys. Looks like I cant count then :) I cant gain access to the car again till the weekend as I had to leave it some ware when they failed. Think I worked out the cause. Had the rear sub frame replaced by a garage and they removed the prop so guess the bastards did not tighten them properly :...

I counted 4 bolts though a connecting peace from the prop on to an X shaped section gear box side?? all 4 bolts had sheared off?? . this is a tec1 sport based C2 2.7 so don't know if they were any different? don't think they are?

Don't know how the hell this has happened But the 4 bolts gear box side have totally sheared in half leaving it spinning and clanging. Looked on oem site but couldn't find part numbers for the nut and bolt. Any ideas? and am I likely to find anything else fooked there when I start sorting it?

I recently put my old golf gti though a test for it to fail on 5 things 2 I knew about but wanted to see the full extent of the problems before I decided if it was worth doing and do them in one go. spent ages getting a steering rack boot off because it was meant to be split to find sod all wrong wi...

I had the top up rules hit me. I had 6 points before taking my car test from my motorbikes. 18 months later i got caught doing 36 in a 30 on what looked like a 40 road. the following month i would have been on 0 points again :( went back on the bikes for 2 years before taking my test again. by the w...

Go to a local sign company with a picture and they will make them up to your spec and fit them for cheaper the sport models come with a double pin stripe down the sides as an alternative http://img151.imageshack.us/img151/5711/03042009057.jpg they cost me £125 front and both sides is that your car ...

5 of the B635S's are in the UK? belonging to any zoners?

took dedication working on her that day hale stones and driving rain

Yep, I have them in mine

Go to a local sign company with a picture and they will make them up to your spec and fit them for cheaper

the sport models come with a double pin stripe down the sides as an alternative

they cost me £125 front and both sides

thanks

So there no problems replacing a facelift head with a cromie one then?

don't you have to change something on the fly wheel and have a lambda sensor added to the exhaust for the 1.3 upgrade?

Hi,

Was just wondering if it was possible to bolt on a hi comp 885 head off a pre facelift on to a low comp bottom facelift end?

I remember reading that the pistons were different shapes? would that effect valve clearances?

BTB3 manifold with longlife stainless the rest

And she sounds like this

[youtube][/youtube]

rear subframe mounting bush gone maybe?

Try the breather pipe running from the crank cover to the inlet manifold. I found the jubilee clip was not done up tight and was casing it run like yours.

Photo of my bonnet

here is my effort

Was hoping you would see this ;) A bad memory got me mixed up with fuse 17 and 16 (Elec seats) I think it was the door/delay relay loom causing the problem. After I replaced it I rechecked the fuses noticed 17 had blown replaced the fuse and it started working again :). I checked this fuse when faul...

Hi

My electric windows will work if a door is open but not if the ignition is on. Checked the fuse its fine. just replaced the whole door purple relay loom and its not that. It has a Bl/Wh wire and Re/Yl wire going to the accessory socket. Any ideas?

thanks in advance

Anyone know what the correct front and back tyre pressure should be?

the disk needs to be made up I had an engineering company make the disk and spacers for me cost me £15. Try and find the zip file the full size picture's are in there along with a diagram of the disk with measurements. I found it using Google or someone on here may have a copy. Alternatively I think...

Job done thanks for advice did not have to undo anything in the sump as I lifted the engine on a jacking point. and unbolted the steering rack.

Oh and yes there was plenty of swearing

as topic

easiest ways of doing this on the drive with no hoist?

thanks in advance

as per topic.

Thanks for response

They only came in silver and gold. Try your local sign makers, take some photos along they may be able to make them up for you for a good price and fit them for you. Think I paid around £125 for mine fitted

Search found 258 matches

starter motor replacement????

Alpina C2 2.7 starter motor?

Re: Faulty ABS pump and hard pressing pedal?

Re: Faulty ABS pump and hard pressing pedal?

Faulty ABS pump and hard pressing pedal?

Re: AIR HORNS...!! Anyone ever fitted them?

Re: Scary Experience

Re: 3.73 or 3.64 diff?

Re: bolts sheard holding prop to gear box

Re: bolts sheard holding prop to gear box

Re: bolts sheard holding prop to gear box

bolts sheard holding prop to gear box

Re: It failed - & I'm relieved ??

Re: Looks Like My E30 Story Is Now Over....

Re: Side stripe decals

Re: alpina archive

Re:

Re:

Re: Side stripe decals

Re: Hi Comp head on low comp block?

Re: Hi Comp engines

Hi Comp head on low comp block?

Re:

Re: squeeking noise from left rear wheel/hub on my e30

Re: Poorly sport. Need some advice..... Vid clip

Re:

Re: April COTM E30s & nature... Competition

Re: Electric windows not working with ignition on?

Electric windows not working with ignition on?

Alpina 16" staggard wheels?

Re: modifying knuckle to fit on e36 rack + few q's

Re: tips for changeing sump M20?

tips for changeing sump M20?

are all pre face lift M20 oil sumps the same?

Re: