Motronic Fault Codes - Revision history

Grrrmachine at 08:22, 1 January 2012

2012-01-01T08:22:13Z

Grrrmachine at 08:21, 1 January 2012

2012-01-01T08:21:46Z

Grrrmachine at 16:49, 23 September 2011

2011-09-23T16:49:28Z

Gortour at 23:15, 26 January 2009

2009-01-26T23:15:35Z

Gortour: New page: '''* NOTE * THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT''' BMW E30 Motronic Fault Codes Procedure for acquiring error code...

2009-01-26T23:13:34Z

New page: '''* NOTE * THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT''' BMW E30 Motronic Fault Codes Procedure for acquiring error code...

New page

'''* NOTE *

THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT'''

BMW E30 Motronic Fault Codes

Procedure for acquiring error codes from Bosch Motronic DME - aka "Stomp Test"

BMW e30 s, which are 1988 and newer, have Bosch Motronic versions M1.1, M1.3 and M.7 and can display fault diagnostic codes. Procedure for obtaining codes is:

For safety reasons, put the transmission in neutral, and turn the ignition key to "On" position but do not start the car
In quick succession fully depress and release accelerator pedal 5 (five) times

After couple of seconds Check Engine light will blink once, and start to flash code(s)

All codes are composed of 4 digits (see table below). For example, code 1211 is represented as Blink, pause, Blink Blink, pause, Blink, pause, Blink

When code(s) start to repeat, all of them have been displayed
Fault Code description

Motronic Fault Code Malfunction Error Description

1211 DME Control Unit - DME, Motronic computer, related fault - which may indicate problem with car computer itself. Delete any stored codes and perform following test: Start the car and let it run for 30 seconds; Turn off car and let it sit for another 30 seconds; Perform diagnostic test again; If the same flash code re-appears DME should be replaced

1215 Air Mass/Volume Sensor 1215 - Indicates problem relating to Air / Mass Flow Meter - AFM or MAF depending on your e30 model. Causes could be cable wire damage, short circuit in the unit, or air / vacuum leak (check air intake hose - big L-shaped one)

1216 Throttle Potentiometer 1216 - Designates error with potentiometer in Throttle Position sensor. Some later model cars have potentiometer, as opposed to switch (TPS) found on majority of e30 s. This code will be active if inappropriate sensor values are read by control unit, and although presence of this fault code may indicate bad potentiometer, wire harness connection at the sensor is common issue (corroded, loose connection, or broken).

1221 EGO Sensor #1 1221 - Fault related to Oxygen ( O2 ) sensor is present if the sensor is unplugged, bad / not-operational, or sensor values are out of range. Test the O2 sensor for proper operation, as well as check harness connections by the sensor and by the battery tray in the engine compartment.

1222 Lambda Control #1 1222 - Lambda control fault code is produced when Motronic system in Bosch control unit receives signal indicating that air/fuel mixture is either excessively rich or excessively lean for period of time loner then 10 seconds. Majority of the causes that affect drivability of the car can be responsible for DME flashing this error:
air leak
defective Air Flow Meter ( AFM)
bad engine temperature sensor
incorrect fuel pressure
problem with injector(s)
defective evaporation system
empty gas tank
issue with spark plugs
problem with valves
etc.

1223 Coolant Temp. Sensor 1223 - This fault code indicates problem relating to Coolant Temperature Sensor (CTS). Test the CTS sensor for proper functionality and check sensor wiring and connections.

1224 Intake Air Temp. Sensor 1224 - Fault with Air Temperature Sensor , which can indicate bad sensor, break or short in wires

1231 Battery Voltage / DME Main Relay 1231 - Battery Voltage / DME Main Relay error code can mean that battery voltage is out of range (either too high or too low), or that battery was disconnected. Test charging system and /or battery to find problem cause.

1232 Throttle Idle Switch 1232 - Error associated with "idle" portion of Throttle Position Switch. Test TPS for proper operation.

1233 Throttle WOT Switch 1233 - Error associated with "WOT" (Wide Open Throttle) portion of Throttle Position Switch. Test TPS for proper operation.

1251 Fuel Injectors (group #1) 1251 - Fuel Injectors (group #1) fault can indicate problem with either individual injector or first group of injectors. Solution is to check fuel injector connectors, wiring from DME to injectors, and to test injector(s) for proper spray pattern. Additionally, fault code 1283 could be set in conjunction with this one.

1252 Fuel Injectors (group #2) 1252 - Same as 1251

1261 Fuel Pump Relay Control 1261 - Fuel Pump Relay Control code indicates break or short circuit associated with fuel pump relay. Test for proper signal on number 3 pin on DME. It can also mean that output stage of DME is faulty (Motronic version 1.3 only)

1262 Idle Speed Actuator 1262 - Possible causes for Idle Speed Control fault are:
damaged wiring to the idle speed actuator
wire from DME is defective
output stage of DME is damaged
Also if engine stalls while it is above 600 RPM, code 1262 will be set

1263 Purge Valve 1263 - Purge Valve fault can indicate that Evaporative Control Valve is faulty, that wire from DME to the valve is damaged, or problem with output stage of DME (Motronic version 1.3 only)

1264 EGO Heater 1264 - EGO Heater error code is stored if there is fault with Oxygen Sensor Heather or it's relay , Air Pump relay, supply wiring, or wire from DME

1444 No Failure 1444 - No errors

←Older revision		Revision as of 08:22, 1 January 2012
Line 1:		Line 1:
−	=~~BMW E30 Motronic Fault Codes~~=	+	=Overview=

	BMW E30s from 1988 onwards have Bosch [[Motronic]] versions M1.1, M1.3 and M.7 and can display fault diagnostic codes. These can be used to identify faults in the system.		BMW E30s from 1988 onwards have Bosch [[Motronic]] versions M1.1, M1.3 and M.7 and can display fault diagnostic codes. These can be used to identify faults in the system.

←Older revision		Revision as of 16:49, 23 September 2011
Line 1:		Line 1:
−
	== '''* NOTE *		== '''* NOTE *

Line 72:		Line 71:

	1444 No Failure 1444 - No errors		1444 No Failure 1444 - No errors
		+
		+	[[Category: Technical]]
		+	[[Category: E30 Engines]]
		+	[[Category: Electrics]]

←Older revision		Revision as of 23:15, 26 January 2009
Line 1:		Line 1:

−	'''* NOTE *	+	== '''* NOTE *
		+
		+	THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT
		+
		+	''' ==

−	~~THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT'''~~

	BMW E30 Motronic Fault Codes		BMW E30 Motronic Fault Codes

@@ Line 1: / Line 1: @@
-== '''* NOTE *
+=BMW E30 Motronic Fault Codes=
-THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT
+BMW E30s from 1988 onwards have Bosch [[Motronic]] versions M1.1, M1.3 and M.7 and can display fault diagnostic codes. These can be used to identify faults in the system.
-''' ==
+'''NOTE:''' THESE CODES ARE NOT RELEVANT FOR UK CARS. THEY ARE ONLY RELEVANT FOR CARS WITH THE "ENGINE CHECK" LIGHT
-BMW E30 Motronic Fault Codes
+For safety reasons, put the [[Drivetrain|transmission]] in neutral, and turn the ignition key to "On" position but do not start the car
 In quick succession fully depress and release accelerator pedal 5 (five) times
-After couple of seconds Check Engine light will blink once, and start to flash code(s)
+After a couple of seconds the Check Engine light will blink once, and start to flash code(s)
 All codes are composed of 4 digits (see table below). For example, code 1211 is represented as Blink, pause, Blink Blink, pause, Blink, pause, Blink
 When code(s) start to repeat, all of them have been displayed
-Throttle Potentiometer 1216 - Designates error with potentiometer in Throttle Position sensor. Some later model cars have potentiometer, as opposed to switch (TPS) found on majority of e30 s. This code will be active if inappropriate sensor values are read by control unit, and although presence of this fault code may indicate bad potentiometer, wire harness connection at the sensor is common issue (corroded, loose connection, or broken).
+=Fault Codes=
-EGO Sensor #1 1221 - Fault related to Oxygen ( O2 ) sensor is present if the sensor is unplugged, bad / not-operational, or sensor values are out of range. Test the O2 sensor for proper operation, as well as check harness connections by the sensor and by the battery tray in the engine compartment.
+{|class="wikitable"
+|-
-Lambda Control #1 1222 - Lambda control fault code is produced when Motronic system in Bosch control unit receives signal indicating that air/fuel mixture is either excessively rich or excessively lean for period of time loner then 10 seconds. Majority of the causes that affect drivability of the car can be responsible for DME flashing this error:
+!Code
 air leak
 defective Air Flow Meter ( AFM)
@@ Line 43: / Line 53: @@
 problem with valves
 etc.
+|-
-Coolant Temp. Sensor 1223 - This fault code indicates problem relating to Coolant Temperature Sensor (CTS). Test the CTS sensor for proper functionality and check sensor wiring and connections.
+!1223
+|Coolant Temp. Sensor
-Intake Air Temp. Sensor 1224 - Fault with Air Temperature Sensor , which can indicate bad sensor, break or short in wires
+|This fault code indicates problem relating to Coolant Temperature Sensor (CTS). Test the CTS sensor for proper functionality and check sensor wiring and connections.
+|-
-Battery Voltage / DME Main Relay 1231 - Battery Voltage / DME Main Relay error code can mean that battery voltage is out of range (either too high or too low), or that battery was disconnected. Test charging system and /or battery to find problem cause.
+!1224
+|Intake Air Temp. Sensor
-Throttle Idle Switch 1232 - Error associated with "idle" portion of Throttle Position Switch. Test TPS for proper operation.
+|Fault with Air Temperature Sensor , which can indicate bad sensor, break or short in wires
+|-
-Throttle WOT Switch 1233 - Error associated with "WOT" (Wide Open Throttle) portion of Throttle Position Switch. Test TPS for proper operation.
+!1231
+|Battery Voltage / DME Main Relay
-Fuel Injectors (group #1) 1251 - Fuel Injectors (group #1) fault can indicate problem with either individual injector or first group of injectors. Solution is to check fuel injector connectors, wiring from DME to injectors, and to test injector(s) for proper spray pattern. Additionally, fault code 1283 could be set in conjunction with this one.
+|Battery Voltage / DME Main Relay error code can mean that battery voltage is out of range (either too high or too low), or that battery was disconnected. Test charging system and /or battery to find problem cause.
+|-
-Fuel Injectors (group #2) 1252 - Same as 1251
+!1232
+|Throttle Idle Switch
-Fuel Pump Relay Control 1261 - Fuel Pump Relay Control code indicates break or short circuit associated with fuel pump relay. Test for proper signal on number 3 pin on DME. It can also mean that output stage of DME is faulty (Motronic version 1.3 only)
+|Error associated with "idle" portion of Throttle Position Switch. Test TPS for proper operation.
+|-
-Idle Speed Actuator 1262 - Possible causes for Idle Speed Control fault are:
+!1233
 damaged wiring to the idle speed actuator
 wire from DME is defective
 output stage of DME is damaged
 Also if engine stalls while it is above 600 RPM, code 1262 will be set
+|-
-Purge Valve 1263 - Purge Valve fault can indicate that Evaporative Control Valve is faulty, that wire from DME to the valve is damaged, or problem with output stage of DME (Motronic version 1.3 only)
+!1263
+|Purge Valve
-EGO Heater 1264 - EGO Heater error code is stored if there is fault with Oxygen Sensor Heather or it's relay , Air Pump relay, supply wiring, or wire from DME
+|Purge Valve fault can indicate that Evaporative Control Valve is faulty, that wire from DME to the valve is damaged, or problem with output stage of DME (Motronic version 1.3 only)
+|-
-No Failure 1444 - No errors
+!1264
+|EGO Heater
 [[Category: Technical]]
 [[Category: E30 Engines]]
 [[Category: Electrics]]